数字卡尺 MAGNET 型号版本

Digital Caliper Case MAGNET Version

2024-04-07 13:18:33

使用说明

所有模型资源均由用户上传分享，内容来源于网络公开资源
侵权投诉：通过抖音私信 @jobsfan 联系我们（需附版权证明），24小时内处理
模型将通过邮件发送（5分钟内自动发送），感谢理解带宽压力，超过1小时没收到，请联系我们

关于费用

我们是爱好者共建社区，为维持服务器成本，每个模型收取微量费用（仅覆盖基础开支）。我们承诺最低成本运营，感谢您的支持！

扫码手机访问

抖音私信 @jobsfan

Summary

A full size case that holds a generic digital caliper

This model is split to be printable and has tongue groves and snap together bits. A very sturdy box case to protect the caliper. Two model options: Latched or Magnets

The assembled project is 246 x 96 x 34 mm
Printable on bed size as small as 200x200
Extra space to hold a 127mm long generic flush cutter

Materials:

LATCHED version BOM: 2x M3x30mm Hex Socket Flat Head Countersunk Bolts Screw or Philips head
Couple inches of scrap filament (for hinge rod)

OR

MAGNET version BOM: 4x 8x2.50mm Magnets
Couple inches of scrap filament (for hinge rod)

Print Instructions:

LATCHED Version files

Latch A - Use Brim
Latch B - Use Brim
Bottom Insert 1 - No Supports
Bottom Insert 2 - No Supports
Bottom Insert 3 - No Supports
Bottom Insert 4 - No Supports
Top Insert - No Supports
Top Plate A - No Supports
Top Plate B - No Supports
Bottom Plate A - Supports only on clasp (see photo)
Bottom Plate B - Supports only on clasp (see photo)

MAGNET Version files

Bottom Insert 1 - No Supports
Bottom Insert 2 - No Supports
Bottom Insert 3 - No Supports
Bottom Insert 4 - No Supports
Top Insert - No Supports
Top M Plate A - No Supports
Top M Plate B - No Supports
Bottom M Plate A - No Supports
Bottom M Plate B - No Supports

Print Assembly:

Before assembly check parts:

a length of filament should freely move through the hinges parts with through holes. The hinge parts without a through hole should be a friction fit with the filament.
LATCHED version: M3x30 screw should easily slide through the Latch A/B files.
MAGNET version: 8x2.50 magnets should snap into slots. Make sure polarity is aligned to attract together!

Assembly time:

Attach ‘Latch A’ to ‘Top Plate A’ and ‘Latch B’ to ‘Top Plate B’ with M3x30 countersunk screws (Do not over tighten). OR if making MAGNET version, press four 8x2.50 magnets into ‘Top M plate A/B’ and ‘Bottom Insert 3’ and ‘Bottom Insert 4’ slots making sure they are oriented to attract each other
On a flat surface, slide fit together:
- ‘Top Plate A’ to ‘Top Plate B’
- ‘Bottom Plate A’ to 'Bottom Plate B'
- ‘Bottom Insert 1’ to ‘Bottom Insert 2’ (a bit of play is normal)
- ‘Bottom Insert 3’ to ‘Bottom Insert 4’ (a bit of play is normal)
Press fit Inserts onto Plates. This will make parts rigid, if not glue can be used
Last step is to make the hinge! Close the box together and use some scrap filament (will be the hinge rod) and push through the hinge until friction fitted and cut off excess.